How to Identify Workplace Hazards Before They Cause Injuries

Table of Contents

Quick answer: To identify workplace hazards, look at your workplace in a structured way: walk through it regularly, talk to workers, review incident and near-miss reports, check safety data sheets and equipment manuals, and break jobs down step by step. Sort what you find into the six main hazard types (safety, physical, chemical, biological, ergonomic and psychosocial), assess the risk of each, then control the highest risks first.

Most workplace injuries don’t come out of nowhere. The hazard was usually there first: a frayed cord, a blocked exit, a heavy lift done the same way for years, a chemical stored in the wrong place. The difference between a safe workplace and an unsafe one is often just whether someone noticed in time.

This guide shows you how to identify workplace hazards systematically, so you can find and fix them before anyone gets hurt. It’s the same core method Ontario uses in JHSC certification training.

Key takeaways

  • Hazard vs risk: a hazard can cause harm; risk is how likely and how serious that harm would be.
  • Six hazard types: safety, physical, chemical, biological, ergonomic and psychosocial.
  • Eight ways to find them: inspections, worker input, incident reviews, job hazard analysis, SDSs, manuals, data and change reviews.
  • Five-step process: prepare, recognize, assess, control, evaluate.
  • Hierarchy of controls: eliminate first and use PPE last.
  • The JHSC’s role: committees are trained to find hazards and recommend controls.

What is a workplace hazard?

A hazard is anything in the workplace that could cause injury or illness: a substance, a piece of equipment, a process, a condition or a behaviour. Risk is the combination of how likely that harm is and how serious it would be.

For example, a wet floor is a hazard. The risk is high in a busy hallway and low in a locked storage room nobody enters.

What are the main types of workplace hazards?

Hazard typeWhat it isExamples
SafetyConditions that can cause immediate injuryUnguarded machinery, slippery floors, working at heights, vehicles, electrical hazards
PhysicalEnergy or environmental conditionsNoise, vibration, heat and cold, radiation, poor lighting
ChemicalSubstances that can harm through contact, breathing or swallowingCleaning products, solvents, fumes, dusts such as silica, asbestos
BiologicalLiving organisms or their by-productsBacteria, viruses, mould, bodily fluids, sharps
ErgonomicHow work is designed for the bodyHeavy lifting, repetitive motion, awkward postures, poor workstation setup
PsychosocialFactors that affect mental health and stressWorkplace violence, harassment, excessive workload, isolated work

Ontario’s JHSC training covers all six categories, including occupational illness, which develops over time and is easy to miss.

8 ways to find workplace hazards

1. Do regular workplace inspections

Walk through every area on a set schedule with a checklist, looking at equipment, housekeeping, exits, storage and how people actually work. Learn more about why workplace inspections matter.

2. Ask the people doing the work

Workers know where the shortcuts, near misses and awkward tasks are. Ask open questions: “What’s the riskiest part of your job?” or “What slows you down or feels unsafe?”

3. Review incidents and near misses

Past injuries, first-aid cases and near misses point straight to hazards. Look for patterns by area, task, shift or time of year.

4. Break jobs down step by step

A job hazard analysis lists each step of a task, the hazards at each step and how to control them. It’s especially useful for new, rare or high-risk tasks.

5. Check safety data sheets

Under WHMIS, every hazardous product has a safety data sheet (SDS) describing its hazards, safe handling and storage. Make sure SDSs are current and accessible.

6. Read equipment manuals and labels

Manufacturer instructions list hazards, guarding requirements and maintenance schedules that are often overlooked.

7. Look at your data

WSIB claims, absenteeism, first-aid logs and maintenance records can show hazards that aren’t visible on a walk-through.

8. Review changes before they happen

New equipment, processes, chemicals, layouts or staff all bring new hazards. Check them before the change, not after.

Need Part 1 and Part 2? Bundle them and save up to $195.

CPO-approved JHSC certification from $570 with an extra $50 off at checkout.

How to identify and control hazards: a 5-step process

Ontario’s JHSC certification training teaches a cycle of recognize, assess, control and evaluate. Here it is as a practical process:

  1. Prepare. Decide which area or job you’re looking at, gather past inspection reports, incident records and SDSs, and bring a checklist.
  2. Recognize. Walk through, observe the work, talk to workers and list every hazard you find, using the six categories as a prompt.
  3. Assess. For each hazard, rate how likely harm is and how severe it would be (see the risk matrix below) to decide what to fix first.
  4. Control. Choose controls using the hierarchy of controls, starting with the most effective option that’s reasonably practical.
  5. Evaluate. Check that the control works and hasn’t created a new hazard, then review it again on a schedule.

How to assess risk: a simple risk matrix

Rate each hazard for likelihood and severity, then use the result to set priorities.

Likelihood ↓ / Severity →Minor (first aid)Moderate (lost time)Severe (critical injury or fatality)
LikelyMediumHighHigh
PossibleLowMediumHigh
UnlikelyLowLowMedium

Fix high risks immediately, plan medium risks with a deadline, and monitor low risks.

How to control hazards: the hierarchy of controls

Not all controls are equal. Work from the most effective to the least:

LevelControlExample: noisy machine
1. EliminationRemove the hazard completelyStop using the machine
2. SubstitutionReplace it with something less hazardousBuy a quieter model
3. Engineering controlsIsolate people from the hazardInstall an enclosure or barrier
4. Administrative controlsChange how people workRotate workers, limit time near the machine, add signs
5. Personal protective equipmentProtect the individualHearing protection

PPE is the last line of defence. It’s often needed, but it shouldn’t be the only control for a serious hazard.

Need Part 1 and Part 2? Bundle them and save up to $195.

CPO-approved JHSC certification from $570 with an extra $50 off at checkout.

Workplace hazard identification checklist

Use this as a starting point and adapt it to your workplace:

Download the workplace hazard identification checklist (PDF)

Get a printable, three-page version with tick boxes grouped by hazard area, a colour-coded risk matrix, a hierarchy of controls quick reference and a hazard log to record what you find, who owns the fix and when it’s due.

  • ☐ Floors, aisles and stairs clear, dry and in good repair
  • ☐ Exits and fire equipment unobstructed and marked
  • ☐ Machine guards in place; lockout procedures available
  • ☐ Electrical cords, panels and outlets in good condition
  • ☐ Ladders, platforms and fall protection inspected
  • ☐ Chemicals labelled, stored correctly, with current SDSs
  • ☐ Ventilation, lighting, noise and temperature acceptable
  • ☐ Lifting tasks assessed; lifting aids available
  • ☐ Workstations set up to reduce strain
  • ☐ First aid kits stocked; first aid trained staff on shift
  • ☐ Workplace violence and harassment risks assessed
  • ☐ Workers alone or in isolated areas have a check-in system
  • ☐ Previous inspection findings followed up

How the JHSC helps identify hazards

In Ontario, the Joint Health and Safety Committee is legally empowered to identify hazards and recommend improvements. A designated worker member inspects the workplace at least monthly, and the committee turns findings into written recommendations that the employer must answer within 21 days. See JHSC member roles and responsibilities.

That’s why hazard identification is at the core of JHSC certification. Part 1 teaches the method. JHSC Part 2 training applies it to at least six hazards in your own workplace, chosen through a workplace hazard assessment. Learn how JHSC Part 2 hazards are selected.

JHSC Certification Bundles

Get Fully JHSC Certified for Less

Take your CPO-approved JHSC Part 1 and Part 2 training together and get an extra $50 off at checkout, on top of sale prices. One simple path to full certification, well within the 12-month window.

E-Learning Bundle

Part 1 self-paced e-learning + Part 2 live virtual

$570

$749

Virtual Bundle

Part 1 + Part 2 live, instructor-led virtual

$690

$885

Flexible virtual dates

Choose your virtual class date now. Need to change it later? Just contact our support team and we’ll help you move to another date.

Add Part 1 and Part 2 to your cart. The $50 bundle discount applies automatically.

Frequently asked questions

How do you identify hazards in the workplace?

Use several methods together: regular inspections, talking to workers, reviewing incidents and near misses, job hazard analysis, checking safety data sheets and equipment manuals, reviewing injury data, and assessing changes before they happen.

What are the six types of workplace hazards?

Safety, physical, chemical, biological, ergonomic and psychosocial hazards.

What is the difference between a hazard and a risk?

A hazard is something that could cause harm. Risk is how likely that harm is and how serious it would be.

What is the hierarchy of controls?

A ranking of ways to control hazards, from most to least effective: elimination, substitution, engineering controls, administrative controls and personal protective equipment.

Who is responsible for identifying workplace hazards?

Everyone has a role under Ontario’s Internal Responsibility System. Employers and supervisors must identify and control hazards, workers must report them, and the JHSC is empowered to identify hazards and recommend improvements.

How often should workplace hazards be assessed?

Continuously, through daily awareness and reporting, with formal workplace inspections at least monthly in workplaces with a JHSC, and new assessments whenever equipment, processes or people change.

Conclusion

Identifying workplace hazards isn’t a one-time job. It’s a habit built on regular inspections, honest conversations with workers, and a simple, repeatable process: prepare, recognize, assess, control and evaluate. Find hazards early, fix the biggest risks first using the hierarchy of controls, and check that your fixes work.

If you want your team to lead this work with confidence, JHSC certification teaches exactly these skills. Explore CPO-approved JHSC certification training.

Get certified to lead hazard identification. Learn hazard selection in Part 2 with 4S Consulting’s CPO-approved JHSC Part 2 training, live with an expert instructor.

JHSC Certification Bundles

Get Fully JHSC Certified for Less

Take your CPO-approved JHSC Part 1 and Part 2 training together and get an extra $50 off at checkout, on top of sale prices. One simple path to full certification, well within the 12-month window.

E-Learning Bundle

Part 1 self-paced e-learning + Part 2 live virtual

$570

$749

Virtual Bundle

Part 1 + Part 2 live, instructor-led virtual

$690

$885

Flexible virtual dates

Choose your virtual class date now. Need to change it later? Just contact our support team and we’ll help you move to another date.

Add Part 1 and Part 2 to your cart. The $50 bundle discount applies automatically.

About the author

Sobi Ragunathan is Vice President of Operations, Strategy & Partnerships at 4S Consulting Services Inc. Sobi supports Ontario employers with workplace health and safety, COR®, ISO 45001, WSIB Health and Safety Excellence program implementation, and JHSC certification training.

JHSC E-Learning Bundle

Part 1 E-Learning + Part 2 Virtual

$570

$749

Flexible virtual dates

Choose your virtual class date now. Need to change it later? Just contact our support team and we’ll help you move to another date.

JHSC Virtual Bundle

Part 1 Virtual + Part 2 Virtual

$690

$885

Flexible virtual dates

Choose your virtual class date now. Need to change it later? Just contact our support team and we’ll help you move to another date.

Scroll to Top
0